Request An Appointment

 

 

What are your thoughts and feelings about Tools You Need to Install a New Bathtub ?

Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task as well as fit attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your washroom if you have already purchased a new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools as well as product list must consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Setup

First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final setting.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

 

 

Setting up the Bath tub

Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub needs to wait till the tub has been used at least when as this will certainly settle it into its last placement.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I am just very eager about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked my post. Are you aware of another individual who is excited about the subject? Be sure share it. I recognize the value of reading our article about How to Install a Bathtub Yourself.

Schedule Your Service